收敛形进气道数值研究的验证

介绍一种新型的、具有最小喉道面积的三维高超声速进气道 (称之为收敛形进气道 )的数值和实验研究结果。表明使用这种形式的进气道 ,在整个飞行速度范围内可以降低阻力和高超声速发动机表面的热防护要求 ,通过降低外压缩表面的倾斜度和减少进气道及燃烧室壁的面积就可以做到这一点。在采用低维次流动的气体动力设计方法的基础上设计成这种形式的进气道。计算是在无粘气体模型构架内用有限体积法进行的。同时用边界层方程计算出计及粘性的气流特性和进气道特性。数值算法是通过收敛形进气道的有限宽楔形外压缩表面的计算和实验数据来验证的。进行实验研究的马赫数M=2～ 1 0 7,基于模型进气道高度的雷诺数Re=( 1～ 5) × 1 0 6。数值计算与实验结果一致性很好。这些结果也和通常的二维进气道的数据作了比较。     

飞翼模型高速风洞PIV试验研究

对小展弦比飞翼标模在2.4米跨声速风洞中创新开展了PIV试验。对空风洞进行了测速校核,并对小展弦比飞翼标模开展了二维、三维涡迹PIV测试,试验马赫数为0.4~0.9。测试结果表明,2.4m风洞PIV试验数据具有较高的准确度,M≤0.8时空风洞测速结果与理论值相差不超过1%,M=0.9时相差不超过2%。小展弦比飞翼标模测试结果显示,M数增大使机翼尾涡涡量和切向速度增大,涡核向内展向方向移动。前缘涡与上翼面分离具有密切关系:当M=0.8、α≤12°时,翼梢测试截面的前缘涡尚未破裂,上翼面未发生显著的流动分离;当α≥13°时,前缘涡破碎时机提前,当地后1/2弦长区域产生了比较明显的流动分离。     

Optimized Fuzzy Clustering Method for Health Monitoring of Shield Tunnels

Since health monitoring of shield tunnels generally employs multiple sensors belonging to different types,a fine analysis on massive monitoring data,as well as further quantitative health grading,is really challenging.An optimized fuzzy clustering analysis method based on the fuzzy equivalence relation is proposed for health monitoring of shield tunnels.Clustering results are auto-generated by using fuzzy similarity-valued map.The results follow the idea of unsupervised classification.Moreover,a convenient new health index HI is proposed for a fast tunnel-health grading.A case study on Nanjing Yangtze River Tunnel is presented to validate this method.Three types of indicators,namely soil pressure,pore water pressure and steel strain,are used to develop the clustering model.The clustering results are verified by analyzing the engineering geological conditions;the validity and the efficacy of the proposed method are also demonstrated.Further,the fuzzy clustering analysis also represents a potential for identifying abnormal monitoring data.This investigation indicates the fuzzy clustering analysis method is capable of characterizing the fuzziness of tunnel health,and beneficial to clarify the tunnel health evaluation uncertainties.     

张力腿漂浮式风力机的运动响应计算

漂浮式风力机与近海桩基式风力机、陆上风力机差异很大,特别是漂浮平台设计复杂,对仿真工具要求更高。海上风力机除受气动载荷之外,还需进一步考虑海洋环境所施加的各种其他载荷。采用自由涡尾迹方法计算风力机气动性能,分别采用线性波和PM频谱模拟波浪运动并应用Morison方程计算波浪载荷。构建张力腿漂浮平台结构动力学方程,以气动载荷和波浪载荷为激励,得到平台响应,并反馈至气动计算,从而完成气动、结构和水动的耦合计算。最后以大型风力机NH1500为例,对张力腿式海上风力机进行仿真模拟,对比分析来流风速、浪高和波浪入流角对漂浮平台运动和风力机气动性能的影响,采用PM频谱模拟真实海况并计算漂浮式风力机动态响应,为漂浮式风力机设计提供了依据。     

飞翼布局无人机变形机翼设计与模型验证研究

对飞翼布局无人机变形机翼和变形机翼传动机构进行了设计,根据设计结果制作验证模型进行风洞实验和外场飞行试验,以此研究伸缩段机翼对飞行器机翼整体气动性能的影响。结果表明:采用变形机翼技术,可以通过实时控制机翼的气动外形保持较高的气动效率,提高飞机在巡航状态下的升力和高速飞行状态下的机动性,满足飞机在各种任务剖面的战术性能要求。     

0.3 m低温风洞液氮供给系统研制

基于系统级的一维热流体模拟分析,建立了适用于研究分析0.3 m低温风洞液氮供给系统的数学模型,并开展了系统漏热、两相流及缓冲罐中液氮容积等流体动力学分析;在系统现有控制策略及试验数据的基础上,基于该数学模型开展了系统压力动态响应分析,获得了在阀门动态调节过程中管网压力的瞬态响应,计算结果与试验值的总体误差控制在10%以内。喷射压力一致化改造避免了阀间干扰,添加的回流管道消除了供给末端的两相流现象,使喷射压力控制精度达到1.1%,调节时间减少到23 s,实现了风洞总温快速安全调节和精确控制。     

舰载直升机理论风限图飞行模拟获取方法

获取舰载直升机实用风限图,仅依靠实装飞行试验或建模仿真都是非常困难的。通过起降飞行模拟试验获取理论风限图,结合少量的海上实装飞行验证试验是一种综合较优的方法。起降飞行模拟试验需要真实飞行员和高等级飞行模拟器参与,飞行模拟器中的母舰气流场数据、母舰运动可由建模仿真或试验测试得到,且必须考虑母舰气流场的非定场特性;只有当飞行员视景或视觉反馈受限时(如能见度降低时),飞行模拟器基座的六自由度运动才是必需的;用DIPES或Bedford方法量化飞行员主观操纵负担,结合记录的客观操纵数据,评判起降难度;典型的飞行模拟试验程序包含了不同风况下的进近和甲板着舰,通常每隔15°和5kn一个风况。通过起降飞行模拟试验得到的理论风限图,可以更加有效和安全地指导海上实装飞行验证试验,最终获得实用风限图。     

基于激光多普勒原理的极低风速测量实验

介绍了利用激光多普勒效应进行风速测量的原理及定点遥测原理,分析了探测气溶胶颗粒大小的要求,并以此搭建了一套极低风速测量系统。同时分析了系统的测速精度,以及安装角度对测量结果的影响。最后分别开展了转台实验、直线导轨实验和风洞实验,实验结果表明,该极低风速测量系统的测量误差基本可以控制在001 m/s以内,当风洞工作介质为未经处理的环境空气时,系统可以获得稳定可靠的信号,测量结果与高性能仪器十分接近。     

Advances in critical technologies for hypersonic and high-enthalpy wind tunnel

Hypersonic and high-enthalpy wind tunnels and their measurement techniques are the cornerstone of the hypersonic flight era that is a dream for human beings to fly faster, higher and further. The great progress has been achieved during the recent years and their critical technologies are still in an urgent need for further development. There are at least four kinds of hypersonic and high-enthalpy wind tunnels that are widely applied over the world and can be classified according to their operation modes. These wind tunnels are named as air-directly-heated hypersonic wind tunnel, light-gas-heated shock tunnel, free-piston-driven shock tunnel and detonation-driven shock tunnel, respectively. The critical technologies for developing the wind tunnels are introduced in this paper, and their merits and weakness are discussed based on wind tunnel performance evaluation. Measurement techniques especially developed for high-enthalpy flows are a part of the hypersonic wind tunnel technology because the flow is a chemically reacting gas motion and its diagnosis needs specially designed instruments. Three kinds of the measurement techniques considered to be of primary importance are introduced here, including the heat flux sensor, the aerodynamic balance, and optical diagnosis techniques. The techniques are developed usually for conventional wind tunnels, but further improved for hypersonic and high-enthalpy tunnels. The hypersonic ground test facilities have provided us with most of valuable experimental data on high-enthalpy flows and will play a more important role in hypersonic research area in the future. Therefore, several prospects for developing hypersonic and high-enthalpy wind tunnels are presented from our point of view.     

高湍流度时全气膜涡轮叶片表面冷却和换热特性的实验研究

为获得高主流湍流度时全气膜涡轮叶片表面的冷却和换热特性,在跨声速风洞中实验研究了质量流量比(MFR)和主流雷诺数(Re)对叶片表面气膜冷却效率和换热系数比的影响。在叶片前缘布置了5排圆形孔,在吸力面和压力面分别布置了3排和6排圆形孔,实验结果由嵌入在叶片中截面的热电偶测得。实验中基于弦长的主流雷诺数的范围为3.0×105～9.0×105,叶栅出口马赫数Ma为0.8, MFR的范围是5.5%～12.5%,主流湍流度Tu为14.7%。实验结果表明:主流雷诺数升高显著增强了叶片表面的换热,使层流边界层到湍流边界层的转捩位置提前。对于吸力面S/C0.2的区域(S/C为当地弧长与弦长之比),气膜冷却效率受MFR影响明显,当MFR大于7.7%时提高MFR会导致气膜冷却效率降低;该区域的换热系数比在中低雷诺数时受MFR影响较小,在高雷诺数时随MFR升高而升高。压力面S/C-0.7区域的气膜冷却效率随MFR升高而升高,-0.7S/C-0.4区域的气膜冷却效率受MFR影响较小,对于整个压力面而言,MFR升高提高了叶片表面的换热系数。相对于叶片其它区域,压力面后半段区域和吸力面的气膜冷却效率受雷诺数影响较大。